| ||||||||
![]() |
| | LinkBack | Thread Tools | Display Modes |
| Sponsored Links |
| ||||||||||||
| Keep us posted. Hope it all gets resolved.
__________________ E2S Moderator Special thanks to RJATV! Visit rjatv.com for all of your atv parts! Support the sand movement! Click here to check out the new duner hangout! ~ www.dunercentral.com ~ |
| ||||||||||||
| I would not keep it but If you keep it, send the case to me and I will weld it for free. Just pay shipping. |
| ||||||||||||
| Quote:
where does this person live? whats their name? ect... post it all over the place,dont be shy about it, their plan was to fuck you, apparently , and he did, so dont be shy about callin him out |
| ||||||||||||
| Give your seller the chance to make it right, throw him under the truck if he fails to do so!
__________________ E2S MODERATOR |
| ||||||||||||
| Quote:
If not...than its time to put the gloves on! ![]()
__________________ E2S Moderator Special thanks to RJATV! Visit rjatv.com for all of your atv parts! Support the sand movement! Click here to check out the new duner hangout! ~ www.dunercentral.com ~ |
| ||||||||||||
| COURTNEY HOLLAND wrote: Josh, I'd like to thank you for the motor. But unfortunately you obviously sent me the wrong one. Based on the previous pictures you sent me this is not that motor. I've identified several inconsistence features between the pictures and the motor you shipped. First being the glob of silicone covering the hole in the case, where there should have been JB weld. 2nd the second JB Weld Spot beneath the shifter( Missing the shifter) 3rd the obvious Red Gasgacinch not appearing in either of the two pictures you sent me as well as the cracked clutch cover which you never mentioned. I feel as though I can never trust someone to come clean and be honest. This was obviously the reason you took your time to return ship this motor to me, after I came out of pocket and sent you my motor. If you had felt at anytime that this was a raw deal you could have contacted me and returned my motor and money. But you felt so inclined as to hope I would send of the exhaust pipe before i got the motor you are sadly mistaken, I trusted you and got burned for a motor and 175 buck, I'm not getting burned for a pipe too. Just so you know what you sent me I've included pictures of what you said you were going to send me and what I got today for your pleasure. P.S. Nice packing job, the damn thing was bouncing around the box when I got it from UPS. Response that WAS the same motor but i did keep the stator cover-my bad,ebay 20 bucks if its that important-also you was going to screw me from the start thats why you changed the deal and kept some of the items you SAID you was going to ship.Those motors go for 600-800 so dont give me that shit!nobody want a kx500 non balanceshaft.Anyways i figured when you fulfilled your end of the deal id send the carb-boot-throttle-airbox-shifter and a few other items you will need for the 86.Its your call-and i didnt take my time,i took no longer than a week maybe 10 days.i knew i would get screwed when you short handed me
__________________ SANDFREEK |
| ||||||||||||
| damn, this guy sounds like a asshole , trying to play the blame game and turn around and make it look like your the bad guy. post who this guy is so it will be known
__________________ 86' honda 250R woods bike fresh motor as of sept. 9th 08' esr trx 5 pipe and silencer 38mm air stryker carb stock cyl. with 68mm wiseco piston (86') cr thin head gasket 180psi compression (stock head) 88' hot rods stock crank with spacer plate vforce 3 reed valve 01 cr250 ignition system +4 axle 13/38 gearing durablue lowering strut maier front and rear fenders |
| ||||||||||||
| If I were you I'd solve this problem with an, address, sack, sock, and a potato. LOL
__________________ 86 Honda 310R Power Valve Paul Turner Eliminator pipe 39mm Sudco racing carb 215psi 110 octane 310esr p/v Ported by Neil at C-Leigh Racing +4 Durablue axle +2 Burgard A-arms 87 Quadzilla Lonestar custom swingarm Lonestar axecaliber axle Lonestar steering stem Powder coated frame Custom Paint 42.5mm mikuni Alky carb (soon to be 48mm Packard Lectron) Marvin Shaw suspension LOTS OF CHROME Trinity Drag port ( I know its Trinity, but do you want to race it ?) CPI oof drag pipe am I forgetting anything? hmmmm ![]() ![]() Never argue with an idiot. They'll just drag you down to their level, and beat you with experience! |
![]() |
« Previous Thread
|
Next Thread »
| Thread Tools | |
| Display Modes | |
| |
All times are GMT -4. The time now is 03:06 AM.
Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0 Credit Counseling | Ringtones | Loans | Nike Air Force 1 | Advertising
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0
vBCredits v1.4 Copyright ©2007 - 2008, PixelFX Studios
Copyright 2005 everything2stroke.com








































E2S MODERATOR



, trying to play the blame game and turn around and make it look like your the bad guy. 



Linear Mode
