| | |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
02-16-2006
| |||||||||||
| |||||||||||
 trans fluid i have an 06 blaster and the local shop told me to put gear savers 80w in it, the manual says 10w 20 or 30 w/e doesnt matter right nowbut i was assured it would be ok...i rode it like 4 times and every time fluid comes out the vent and pours all over my header..how much fluid does a blaster take? can i use motor oil? idk help me out thanx. Last edited by candiria05; 02-16-2006 at 02:43 AM.      |
| Sponsored Links |
|
02-16-2006
| |||||||||||
| |||||||||||
| If its coming out the over flow..id say you put too much in. get a good measuring device and put the 650ml in it. What kind of 80w are you using? |
|
02-16-2006
| ||||||||||||
| ||||||||||||
| i think a blaster requires 1500cc of tranny fluid
__________________ 2005 YZ250 - FMF Gold Series Fatty Pipe, Titanium 2 Silencer, UNI Filter 2006 YZ450F - White Bros Full Carbon Exhuast, UNI FIlter  92% of teens have switched to rap music if you are part of the other 8% put this in your sig. |
|
02-16-2006
| ||||||||||||
| ||||||||||||
| the manual says- yamalube 4 10w-30 .65L (.69 us QT) |
|
02-16-2006
| |||||||||||
| |||||||||||
| blsters take less than a quart and there should be a little window to check the level. |
|
02-16-2006
| ||||||||||||
| ||||||||||||
| 650cc for every oil change. 675cc whenever you open the cases of clutch side cover. It shouldn't be coming out any vent?
__________________  JB Racing +2 Swingarm RV Racing dual row bearing carrier RPM Dominator +4 axle Works Ultra Cross rear FourPlay +3+1 A-arms Elka dual rate fronts StreamLine SS braided brake lines Fasst Flexx bars LSR anti-vibe stem Rox bar riser Magura Hydraulic clutch Acerbis hand guards Graydon nerf bars Roll Design race pegs AC Racing front/rear bumpers FloTek Ported big-bore 3mm stroker / head / flywheel Pro Design intake Keihin Air Striker 36mm pwk carb V-Force Delta II reeds PB Plastics Factory7 exhaust PB aluminum airbox UNI filter ProDesign powershifter HiPer carbon fiber beadlocks Maxxis iRazrs IMS 4 gallon tank |
|
02-16-2006
| ||||||||||||
| ||||||||||||
| yeah umm....I was gonna say, There is no vent....for the tranny case...well there is a vent hose...but in no way would that leak on the head pipe...You['ve got a different problem ther ebuddy.... and it uses 650mL, and don't waste your time looking at that little class thing.. its not going to tellyou much...
__________________ Saul 1998 Yamaha Banshee Pro Circuit pipes, K&N filter, removed lid, boost bottle, Pro Taper bars, Ceet graphics, Durablue Extended rear axle, powermadd handguards, Joker Machine dual headlights, Boyesen Carbon Fiber reeds, MSR gripper levers FLOTEK porting, .035 shaved head, 200w stator, +4 timing advance, Streamline Billitanium Steering stabilizer, New Wiseco pro-lites (.020),Pro Armor Tether, Moose TORS Elimator Kit w/ braided stainless steel throttle cable, K&N Outerwear and a whole lot of ass kicking. Friend the clutch...too much power. 2006 Yamaha YZ 125 05 Ski Doo MXZ 500SS Adreneline 2007 GSXR 600 My first four stroke! Full Scorpion exhaust, Vortex clipons E2S militia member |
|
02-16-2006
| |||||||||||
| |||||||||||
| I had gear oil come out of mine before, 1. Make sure that its not over full, it takes 650ml like Maine said. 2. If it is filled correct, you may have a problem such as a bad case gasket or a crack letting pressure from your crankcase area puch into the trans area causing oil to be pushed out the vent. Hopefully, its just over full |
|
02-16-2006
| |||||||||||
| |||||||||||
| Blasters are bad for blowing clutch cover gaskets when you overfill the transmission. Most times it will blow out right beside the transmission vent nipple & spray oil on the pipe & down the swingarm & on the rear brakes. Next time any of you guys have a blaster engine apart, look & see where the oil in the clutch cover can get back into the transmission part of the cases. You will be surprized. Neil |
|
02-17-2006
| |||||||||||
| |||||||||||
| oil from the vent and onto the tube can be a few things... 1 overfull, 650Ml of gearsaver 80w is fine, thats what i use 2 bad crank seal, allowing pressure to build in the crankcase and pushing out of the vent...happened to me ....i have NEVER seen a blaster blow a clutch cover gasket since, well, 89 when i started messin with them. also, if the clutch cover gasket was leaking, it wouldnt make it leak out the vent tube onto the head pipe. ps, for the ones who dont know...the case vent tube runs up along the frame and under the hood above the headpipe.
__________________ Blaster mods list LRD pipe and silencer Wiseco pro lite .040 Milled head Ported/Polished Moose racing engine seals Vitos degree key Mikuni 28mm flatslide Motion pro cables +3.75" swingarm +2/+1 Burgard a-arms 400ex rear shock Shockwears K&N w/outerwears lid Maxxis razrs Banshee hydro brakes 14/38 gearing Banshee axle Banshee rims Boyeson reeds Alba pro elite bumper Maier plastics Vitos oil blockoff Vitos reed spacer AC nerfs IN SEARCH OF cheap grab bar, banshee rear rims, silver maier rear plastics |
|
« Previous Thread
|
Next Thread »
| Thread Tools | |
| Display Modes | |
Linear Mode
| |
All times are GMT -4. The time now is 11:07 AM.
Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0 Credit Cards | Credit Reports | Secured Loans | Mortgages | Internet Advertising
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0
vBCredits v1.4 Copyright ©2007 - 2008, PixelFX Studios
Copyright 2005 everything2stroke.com
