| | |||||||
| | LinkBack | Thread Tools | Display Modes |
07-14-2008
| ||||||||||||
| ||||||||||||
 LSR arms, laeger swing arm, elkas I just bought a narrow front end, CR500 link frame, so I will be needing to swap some stuff. LSR +2s powder coated black, I may put a fresh coat on. New ball joints and bushings coming soon. Elka triple rate zps std travel front shocks Laeger swing arm -2? (I can measure if needed, I actually liked it better than stock length) rough silvervein powder coat, plan to powder coat black Elka zps rear shock with protective gold titanium nitride coating on shaft Right now I am looking for interest because they are not fully ready to sell yet. I will post pictures when ready, PM or call 319-404-7029 for any questions/offers. The arms/shocks are in my sig. I would be willing to trade toward a +3 long travel front end, preferably elkas and durable arms that can accept stock spindles or similar (ex. not t-pin).
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs  Last edited by 88mxR; 07-14-2008 at 09:12 PM.     |
| Sponsored Links |
| |
|
07-14-2008
| ||||||||||||
| ||||||||||||
| Can you precisely measure the swingarm from pivot bolt center to carrier center? Also what are the shocks set up for?
__________________ Full Roll Design Lobo 250R Full Walsh 250R Dune/Drag 250R |
|
07-15-2008
| ||||||||||||
| ||||||||||||
| Fronts - 160lbs mx Rear - 180lbs mx
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs |
|
07-15-2008
| ||||||||||||
| ||||||||||||
| please post prices...per the for sale forum guidelines. thanks.
__________________  E2S Moderator Special thanks to RJATV! Visit rjatv.com for all of your atv parts! Be apart of the sand rider community. Check out the #1 Duner Hangout! ~ www.dunercentral.com ~ |
|
07-15-2008
| ||||||||||||
| ||||||||||||
| Here are the elkas, pics of the rest coming soon. Its hard to give these up, but I can't run my same front end on the narrow frame without goofy rims. Image of elkas - Photobucket - Video and Image Hosting 
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs Last edited by 88mxR; 07-15-2008 at 08:03 PM. |
|
07-15-2008
| ||||||||||||
| ||||||||||||
| Sorry, I'm not sure how to show it on the thread. The link will have to do.
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs |
|
07-15-2008
| ||||||||||||
| ||||||||||||
| ...prices???
__________________ E2S Moderator Special thanks to RJATV! Visit rjatv.com for all of your atv parts! Be apart of the sand rider community. Check out the #1 Duner Hangout! ~ www.dunercentral.com ~ |
|
07-15-2008
| ||||||||||||
| ||||||||||||
| I'm watching ebay auctions to see what they are worth, offers are welcome. Like I said not everything is ready yet; most isn't off the quad yet. I'm also waiting on ball joints because the current ones were old and a boot was torn. I'll keep you guys posted.
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs |
|
07-16-2008
| ||||||||||||
| ||||||||||||
| Pics of the rear shock and swing arm: Image of elka rear - Photobucket - Video and Image Hosting Image of elka rear 2 - Photobucket - Video and Image Hosting Image of Laeger Swing Arm - Photobucket - Video and Image Hosting All components worked great; they seemed to soak up everything. As stated before, I didn't want to get rid of it, but the new frame will need different parts to keep width and function properly. Here are the prices, shipping included: Elka Fronts - $1100 new, $450 LSR +2 arms, new ball joints, new bushings- $350 (will be ready soon) Elka Rear - $1100 new after coating, $475 Laeger swing arm, fresh black epoxy paint - $350
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs |
|
07-17-2008
| ||||||||||||
| ||||||||||||
| Elka fronts - around 16.5" eye to eye Laeger Swing Arm - around 17.25" center to center
__________________ 88 250r Motor - 4mm stroker mx ported, Sparks pipe, 38mm AS, v force reeds, Hinson basket w/ Barnett plates Chassis - PRD narrow frame, Janssen +3 arms, Ohlins LT big bodies, cr500 link Walsh swing arm, Ohlins rear shock, LSR axle, Denton stabilizer, AC propegs |
| Thread Tools | |
| Display Modes | |
Linear Mode
| |
All times are GMT -4. The time now is 02:10 AM.
Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0 Deutsch | Web Advertising | Credit Cards | Remortgages | Homeowner Loans
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0
vBCredits v1.4 Copyright ©2007 - 2008, PixelFX Studios
Copyright 2005 everything2stroke.com
