| | |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
04-04-2008
| ||||||||||||
| ||||||||||||
 Hydraulic Brakes Tossed out the cable brake and threw in a a Hydro Caliper along with a new disc.  No locknuts to hold the disc in place. It's held by clips & boots, the caliper keeps it in place. Make sure boots are greased, two clips hold it down, one for the axle, one for the disc.  Left side installed..  Right side installed..       |
| Sponsored Links |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| Caliper slides right into place.   You have to shave the stock retainer tab to install the new bracket w/master cylinder.   |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| While at it I installed that lower motor mount bolt I was missing. Special thanks to member johnmummie for the freebie!!! I later stripped the drain plug, I guess I'll finally get that magnetic drain plug I always wanted lol.. Hydro front brakes coming soon  
__________________  E2S MODERATOR |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| So the rotor is a floating kind? Did the whole kit bolt right up without any mod's to the bike?
__________________ My bikes Foster Bike 00' Banshee (Shit my buddy don't ride it!) 84' FXE Shovelhead 72' Norton Chopper |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| how much did that setup cost? looks like it went in easy. need that for mine when i get a job again.
__________________ ANDY  my 2000 blaster foam filter from toomey 4 degree key from dustin420 toomey b1 oil block off kit Boysen power reeds worn out stock front tires 20x11x8 razr bored .020 over 3mm stroker have flotek port and polish to match stroke this winter now that my 13 month vacation is over |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| Nice work bro! Perfect fit!
__________________  E2S Moderator Special thanks to RJATV! Visit rjatv.com for all of your atv parts! Be apart of the sand rider community. Check out the #1 Duner Hangout! ~ www.dunercentral.com ~ |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| realyy nicee job
__________________ 1999 yamaha blaster/.020 bored/wiseco pro lite piston/lrd exhaust/vforce3/3mm stroker stuffer crank/14 tooth front spocket/tusk clutch/flotek ported and polished cylinder/shaved head/lighten flywheel/rounded shiftstar/35mm kehium carb and filter/douglus red label rear rims/perellii race rail tires/oil injector block off/protaper bars/powermadd handguards/black maier plastics and hood/dg grab bar/dg bumper/dg nerf bars/pro armor killswitch  |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| Quote:
Quote:
The Shee should be ready tonight, we made up & on good speaking terms now lol!! Quote:
 Quote:
A few washers and a bit of paint & you're done! Bleeding it is quiet a task but I'll get it done.  
__________________ E2S MODERATOR Last edited by climb any hill; 04-04-2008 at 05:40 PM. |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| climb, have ever thought about writing step by step books? the pics and how you did is great!! should help alot of blaster owners out, especially when it looks so easy to do
__________________  |
|
04-04-2008
| ||||||||||||
| ||||||||||||
| waiting on the union and the company to decide what they are doing. is it a calaper and master cylinder. where would u get lines, how much?
__________________ ANDY my 2000 blaster foam filter from toomey 4 degree key from dustin420 toomey b1 oil block off kit Boysen power reeds worn out stock front tires 20x11x8 razr bored .020 over 3mm stroker have flotek port and polish to match stroke this winter now that my 13 month vacation is over |
|
« Previous Thread
|
Next Thread »
| Thread Tools | |
| Display Modes | |
Linear Mode
| |
All times are GMT -4. The time now is 06:40 PM.
Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0 Unblock Myspace | Best Credit Cards | Car Insurance Quote | The Latest Gadgets | Credit Cards
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.1.0
vBCredits v1.4 Copyright ©2007 - 2008, PixelFX Studios
Copyright 2005 everything2stroke.com
